TETRIS series active probe (FET probe)

TETRIS Active Probe will be able to contact in parallel to the pins of 2.54mm pitch in close proximity. The housing of this probe is T-shaped, and the probes can be stacked without restriction by stacking them one after another. In this way, multiple measurements can be performed simultaneously.
■ High input impedance: 1 MΩ, low capacitance: 0.9 pF ■ Replaceable tip spring tip ■ Can contact IC leads of 2.54 mm pitch in close proximity ■ Can be connected to any 50 Ω input measuring instrument
The TETRIS active probe was produced as an independent measurement system by a probe manufacturer for oscilloscopes. The small form factor and convenient accessories simplify your measurement tasks. Not only does it fit tightly in tight spaces, but it can also contact very small test points and vias.
■High input impedance in the frequency band DC up to 2.5 GHz
With an input resistance of 1 MΩ and an input capacitance of 0.9 pF, TETRIS is suitable for measuring all frequency ranges. All 3 models cover the band from DC to 2.5 GHz.
The ground plane and the use of copper pads allow the GND connection to be kept as short as possible for measurements close to the true value on the IC.

Scope of delivery The following items are included in the scope of delivery :
■ Probe ■ Spring Tip ■ Solid Tip ■ L-In Adapter ■ Ground Blade ■ 2 self-adhesive Cu-pads	■ Ground Lead 6 cm ■ Ground Lead 12 cm ■ Ground Lead 90° 5 cm ■ Ground Lead 90° 10 cm ■ Y-lead adapter to 0.8 mm sockets ■ Picohook™ black	■ Picohook™ red ■ Marker Bands 4 Colors ■ Z-Ground ■ PCB Adapter ■ Ground Leaf ■ Power Supply

Model	TETRIS 1000	TETRIS 1500	TETRIS 2500
Order-No.	881-000-INT	881-500-INT	882-500-INT
Attenuation ratio	10:1
Input RC	1 MΩ // 0.9pF
Input coupling	50 Ω
Frequency bandwidth (Probe Only)	1.0 GHz	1.5 GHz	2.5 GHz
System bandwidth (-3dB)	600MHz	1 GHz	2 GHz
Dynamic measuring range	± 8 V
Maximum input voltage	20 V
Cable length	1.3 m

	Wide bandwidth / High voltage differential probe BumbleBee^® (PMK GmbH - Germany)
	High voltage differential probe SS-320
	High voltage differential Paired probe for PDD series (PMK GmbH - Germany)

Differential HV-Probe

Wide bandwidth / High voltage differential probe BumbleBee® (PMK GmbH)

Wide bandwidth DC - 400MHz

BumbleBee^® Accerrories ^*5

BumbleBee^® Specifications ^*1

Item			Specification
Attenuation (switchable)			50:1	100:1	250:1	500:1
System Bandwidth (-3dB)		Input Voltage 50V	300MHz		400MHz
		Input Voltage 500V	-		300MHz
		Input Voltage 1,000V	-			300MHz
Risetime (10% - 90%)		Input Voltage 50V	1.2ns		875ps
		Input Voltage 500V	-		1.2ns
		Input Voltage 1,000V	-			1.2ns
Noise (rms) *2 (Referred to the input)			55 mV		75 mV
Typical Propagation Delay			10 ns
Max. Input Voltage		measurement category Ⅰ	2,000 V rms 6,000 V transient Overvoltage
		measurement category Ⅲ	1,000 V rms CAT Ⅲ
		Pollution Degree	2
		Max. Differential Input Voltage (incl. AC peak)	± 200 V DC	± 400 V DC	± 1,000 V DC	± 2,000 V DC
		Common Mode Voltage	± 2,000 V pk (± 1,400 V rms)
DC Gain Accuracy			± 0.7%		± 0.35%
Offset Range *3			± 4 V
Offset Resolution *3			15 Bit / Minimum Step < 125 μV
Offset Drift *3			150 μV/ºC		40 μV/ºC
Input Impedance		Each Input to Ground	5 MΩ // 4 pF
		Differential Input Impedance	10 MΩ // 2 pF
Input Coupling of the Measuring Instrument *4			50 Ω
Typical CMRR		DC	> 80 dB
		100 kHz	> 70 dB
		1 MHz	> 62 dB
		3.2MHz	> 50 dB
Probe power supply			PS-02 (2ch) , PS-03 (4ch) Probe power supplies provides PC remote control on Bumble Bee via USB or Ethernet(Optional) with PC-software "PMK Probe Control(64bit-Win7 or above version)" with USB memory.
Mechanical Specifications		Weight (probe only)	370 g
		Cable Length	2m
		Input Lead Length	25cm
		Input Lead Connectors	2 x 4 mm (male)
		IOutput Connector	BNC (male)
Environmental Specifications	Altitude		operating : up to 2,000 m 　non-operating : up to 15,000 m
	Temperature Range	Probe	operating : 0 °C up to 50 °C non-operating : 20 °C up to 70 °C
		Input Leads	operating : -40 °C up to 85 °C
	Maximum Relative Humidity		80 % relative humidity for temperatures up to 31° C, decreasing linearly to 40 % at 50° C

*1 Measured at 23°C environment connected to PS-02/PS-03 power supply(optional)
*2 Broadband Noise, Bandwidth 30 MHz
*3 Referred of output
*4 Must be met to achieve best performance and avoid Damage to the Probe
*5 Parts#890-880-104 : Twinholder M6 and 890-880-112 : Pair of Rail Clip Connectors 4mm are optional. 

Sonic 4000 (High Frequency FET probe)

Sonic Active Probe 

■ 4.0 GHz
■ 0.6 pF Input Capacitance
■ wide dynamic range
■ ultra low noise

The Sonic active probe is available as of now. It has the same Input Voltage of 20 V as the TETRIS® Series of Probes, but shows bandwidths of up to 4 GHz. The various accessories provided within the scope of delivery offer the same connections and adaptations as the accessories of the TETRIS® Series. A Power Supply PS-02 or PS-03 is required to function.

Model	Sonic 4000 Active Single end probe
Attenuation ratio	10:1
Input RC	1 MΩ // 0.6pF
Input coupling	50 Ω
Frequency bandwidth (-3dB)	DC ~ 4GHz
Dynamic measuring range	± 8 V
Maximum input voltage	20 V
Cable length	1.3 m